0

Shopping cart

All Categories

Gorilla Wood Glue 18oz Stronger, Faster Wood Glue With Shorter Clamp Time. Ideal For Building, Carpentry Or Hobby Projects Using Any Type Of Wood 18oz 6205001

SKU: 6205001/6205003 Categories: , Tags: , Brand: Gorilla

Compare

Gorilla Wood Glue 18oz Stronger, Faster Wood Glue With Shorter Clamp Time. Ideal For Building, Carpentry Or Hobby Projects Using Any Type Of Wood

 

 

1.Application:-

For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet.

 

2.
The technique and type of clamp to be used is determined by many factors: the specific type of joint, type of stock or lumber, moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied.

Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood.

Cure Time (amount of time for glue to reach total bonding strength): 24 hours

3. Clean Up
Clean up while glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, sand as needed. Wash hands, skin and damp cloths in soap and warm water, then rinse.

Clean up when glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse.

Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water.

To remove Gorilla Wood Glue from hands, wash with warm soap and water.

Storage:-
To extend shelf life, keep the container sealed and stored at 55°F-75°F. Gorilla Wood Glue will not harden in the bottle as long as the cap is closed and water is not allowed to evaporate from the bottle. This is freeze/thaw stable. If the glue is frozen, thaw at room temperature. If necessary, shake vigorously to restore to original consistency.

Finishing:-
What is the Dry Color?– Gorilla Wood Glue dries a natural translucent tan color, without an orange after-glow.

Painting – Gorilla Wood Glue can be sanded and painted.

Stains and Dyes – Gorilla Wood Glue can be stained and dyed. However, the color may be a shade off the wood being glued. Water-soluble food coloring type dyes and water based stains can be mixed into the glue before the glue is applied to the wood to get a closer color match. Experiment with varied mixtures to achieve the closest match to the final color desired.

Sealers, Urethanes, Varnishes, and Shellacs – Gorilla Wood Glue can be sealed.

Wood Fillers – Gorilla Wood Glue can be used as a wood filler. To ensure homemade wood fillers adhere to the surface, use the finest dust particle of wood possible when mixing with the glue. Also, make sure the ration of glue creates a toothpaste consistency. Use sparingly, as the product will not stain consistently with the surrounding wood.

 

Application Tips
Application Temperature – For maximum performance, the recommended application temperature for Gorilla Wood Glue is 70°F, but it can be applied as low as 55°F. If application temperature exceeds 70°F, you can expect the assembly time to be shorter. Other important temperatures: Once cured, extreme cold will not affect the holding power of Gorilla Wood Glue. When exposed to extreme heat (near 220°F), the bond can hold but only at a fraction of its normal strength.

Hard To Glue Woods – The hardest of exotic woods, like ebony, may present some glue absorption problems and may be too smooth for gluing. Also, harder woods, when burnished during planing, present problems for gluing as the surface gets very shiny and slick.

Achieving the optimal gluing surface should be done by sanding using higher grit sandpaper (220+). Lightly sand to ensure open surface pores and remove any glazing.

Oily woods can also be more difficult to bond due to oil resistance to water. The best solution for oily woods is to wipe them down with rubbing alcohol or acetone to cut and remove the oil from the wood surface. Glue after the solvent has dried completely on the surface.

Clamping – Factors that affect clamping include the specific type of joint, type of stock or lumber, moisture content of stock, room temperature, assembly time, and surface quality.

  • 5 Stars
  • 4 Stars
  • 3 Stars
  • 2 Stars
  • 1 Stars

Average Star Rating: 0.0 out of 5 (0 vote)

If you finish the payment today, your order will arrive within the estimated delivery time.

Reviews

There are no reviews yet.

Be the first to review “Gorilla Wood Glue 18oz Stronger, Faster Wood Glue With Shorter Clamp Time. Ideal For Building, Carpentry Or Hobby Projects Using Any Type Of Wood 18oz 6205001”
Select your currency
USD United States dollar
×